What the main CAN bus terms mean
CAN bus is the two-wire network that lets a vehicle's control units talk to each other, and almost every term below describes either how that network is wired, what it carries or how a signal gets from it to an accessory. Each entry has a short definition and a note on where it matters in an install.
- 12V and 24V systems
-
Cars and vans run a nominal 12 V electrical system. Most heavy trucks and coaches run 24 V, usually from two 12 V batteries in series, with the charging voltage sitting a little above nominal.
Where it matters: Anything switched or powered from the vehicle has to be rated for that voltage, which is why a truck job needs checking before a van-spec part goes in.
- Accessory output
-
A feed that is live in the accessory and run positions of the key and dead once the key is out. Radios, cameras and trackers connect to it so they come up with the vehicle and stop drawing current when it is parked.
Where it matters: On a CAN vehicle the accessory state is a network message, so the feed has to be created from that message.
- Bus load
-
The share of the available bandwidth that messages are using, shown as a percentage. A bus near its limit delays its lower-priority messages.
Where it matters: A device that only listens adds no frames and leaves the load alone, while one that transmits adds to it.
- Bus sleep and wake-up
-
Control units cut their current draw by going to sleep when nothing needs them, and the bus falls silent. A wake-up event such as a door opening or a key signal brings the modules, and the traffic, back.
Where it matters: Equipment listening to the network sees nothing while it sleeps, so it has to cope with both states without draining the battery.
- CAN bus
-
Controller Area Network, a two-wire serial network standardised as ISO 11898 that lets control units exchange short messages with no central host. Every message carries an identifier, and when two modules transmit together the lower identifier wins.
Where it matters: Nearly every signal a retrofit accessory needs, from speed to reverse, now travels on this network as a message.
- CAN FD
-
CAN with Flexible Data-rate, defined in ISO 11898-1. A frame can carry up to 64 data bytes instead of 8, and the data part can be sent faster than the part that settles who transmits.
Where it matters: Some newer vehicle networks use it, so a reader has to understand that frame format as well as classical CAN.
- CAN high and CAN low
-
The two conductors of a high-speed CAN bus, shortened to CANH and CANL. Modules transmit by driving them in opposite directions, and receivers read the difference between the two rather than either voltage alone.
Where it matters: Finding this pair correctly is the first step of any connection, and it is the pair you never cut.
- Contactless (inductive) reader
-
A pickup that reads bus traffic by coupling to the wire through its insulation, instead of through an electrical splice. Nothing is cut or soldered, so the loom stays as the factory left it.
Where it matters: How well it works depends on the cable and its routing, so the method suits some vehicles better than others.
- ECU
-
Electronic control unit, the embedded computer behind a vehicle function such as the engine, brakes, gearbox, body or instrument cluster. A modern vehicle carries many, each sending and receiving messages on one or more buses.
Where it matters: The speed you want normally starts in the braking or gearbox unit, and an interface decodes that unit's message.
- FMS
-
The Fleet Management System interface, a specification agreed by European truck and bus makers. It exposes a defined set of vehicle data, such as speed and engine speed, from the J1939 network to telematics equipment.
Where it matters: Where a truck offers it, a fleet device reads a set list of values instead of the whole bus.
- Gateway
-
A control unit that joins separate CAN networks and passes selected messages from one to the other. It keeps, say, the powertrain network apart from the body network.
Where it matters: A signal present on one network may be absent from the other, which decides where an interface has to join.
- Ignition live
-
A wire carrying battery voltage only while the ignition is on, normally switched by a relay in the vehicle. CAN vehicles report the ignition state as a message, so the equivalent wire can be recreated from it.
Where it matters: It is the reference most add-on kit uses to know when to wake and when to stop.
- Isolated CAN
-
A CAN connection with galvanic isolation between the bus side and the equipment side, usually through an isolated transceiver and supply. It breaks ground loops and stops a surge on one side reaching the other.
Where it matters: Long vehicles have long earth paths, where differences in ground potential are larger.
- J1939
-
SAE J1939, the CAN-based protocol family used on heavy trucks, buses, off-highway machines and marine engines. It uses 29-bit identifiers, defines named signals such as wheel-based speed and engine speed, and commonly runs at 250 kbit/s.
Where it matters: It makes signal reading more uniform across heavy-vehicle makes than on cars and vans, where each manufacturer defines its own messages.
- LIN
-
Local Interconnect Network, a single-wire, low-cost bus for simple devices such as mirror motors and switch packs. One master polls the other nodes, and the speed tops out at 20 kbit/s.
Where it matters: LIN traffic is not on the CAN pair, so a switch on a LIN branch only reaches the CAN network through a body control unit.
- Listen-only mode
-
A CAN controller setting in which the node receives frames but does not acknowledge them or transmit anything. To the rest of the network it is invisible.
Where it matters: Reading speed this way leaves the vehicle's own traffic untouched, which an on-demand diagnostic request cannot do.
- Negative output
-
A switched output that connects the load to ground when active, also called a low-side or sinking output. The load stays connected to a positive feed and the output completes the circuit to earth.
Where it matters: Many camera and screen triggers expect this polarity, so check what the receiving device wants before choosing the output.
- OBD-II port
-
The 16-pin diagnostic connector defined in SAE J1962, fitted to cars and light vans within reach of the driver. On CAN vehicles pin 6 is CAN high, pin 14 is CAN low and pin 16 is permanent battery positive.
Where it matters: It is easy to reach, but what a plug-in device can read there depends on how the manufacturer has arranged access.
- Positive output
-
A switched output that supplies battery voltage to the load when active, also called a high-side or sourcing output. The load is wired between the output and earth.
Where it matters: Lighting and accessory triggers commonly use this polarity.
- PTO
-
Power take-off, a drive taken from the engine or gearbox to run auxiliary equipment such as pumps, compressors and tail-lifts. Engagement is normally permitted only within set engine-speed or road-speed limits.
Where it matters: Those limits are enforced from the engine speed and road speed signals read off the network.
- Relay
-
An electrically operated switch in which a small coil current closes contacts that carry a much larger load current. Automotive relays commonly have four or five pins.
Where it matters: A low-current output usually drives the coil, and the contacts then carry the lamp, motor or beacon.
- Runlock
-
A function that keeps the engine running with the key removed and the vehicle locked. It cuts the engine the moment a safety condition, such as a pedal press or released handbrake, is broken.
Where it matters: The conditions it watches are read off the network, so wiring into each circuit is avoided.
- Secure gateway
-
A gateway that filters or authenticates what reaches the diagnostic port and the internal networks, so unapproved requests are dropped. It guards against tampering, and it also blocks some plug-in devices from reading the bus through the OBD port.
Where it matters: Where one is fitted, a connection that relies on diagnostic requests may not get an answer.
- Speed pulse
-
A square-wave signal whose frequency rises in step with vehicle speed. Receiving equipment is set to a number of pulses per kilometre, so the wrong figure makes it read high or low in proportion.
Where it matters: Older trackers, limiters and tachograph inputs expect this form, and a CAN interface can produce it.
- Switched output
-
An output that an interface turns on and off in response to a vehicle condition such as reverse gear or ignition, instead of being permanently live.
Where it matters: It is how a vehicle state becomes a trigger a camera, lamp or relay can act on.
- Tachograph
-
A regulated recording instrument in goods and passenger vehicles that logs speed, distance and driver activity. It takes its motion data from an approved source and is calibrated by an approved workshop.
Where it matters: What may feed it is set by the tachograph maker and the regulations, so confirm the input before connecting anything.
- Termination
-
A 120 ohm resistor at each end of a high-speed CAN bus that stops signals reflecting off the ends of the cable. With the power off, a correctly terminated bus measures about 60 ohms across CAN high and CAN low.
Where it matters: The vehicle already has its two resistors, so an accessory connection should never add a third.
- Twisted pair
-
Two insulated conductors wound round each other. Interference reaches both wires almost equally and cancels at the receiver, which is why CAN uses the arrangement.
Where it matters: Keep the twist right up to the connection point when working on the pair.
- UDS
-
Unified Diagnostic Services, ISO 14229, the request and response protocol workshop tools use to read fault codes, run tests and reprogram control units. On CAN it travels in frames carried by the ISO 15765-2 transport layer.
Where it matters: Manufacturers can restrict which services are open to third-party devices.
- VSS (vehicle speed sensor)
-
The sensor, or the signal it produces, that reports how fast the vehicle is moving. It was once a toothed wheel and pickup on the gearbox output, and is now usually calculated from wheel-speed sensors and shared as a CAN message.
Where it matters: Equipment that still asks for a VSS input needs the network value turned back into a pulse.
Sources
- ISO 11898-1: Road vehicles, Controller area network (CAN), data link layer and physical signalling, ISO
- Introduction to the Controller Area Network (CAN), SLOA101B, Texas Instruments
- SAE J1939 standards collection, SAE International
- SAE J1979: E/E diagnostic test modes (OBD-II), SAE International
Talk to us about a CAN bus job
Tell us the vehicle and the signal you need, and our engineers will point you to the right interface.