CAN bus interface modules for vehicle conversions and accessories, designed and made in the UK
Vehicle-fit interface modules from a UK manufacturer, with in-house R&D and firmware, for installers, converters, fleets and OEMs.
Last updated:
Who manufactures CAN bus interface modules in the UK?
Scorpion Automotive designs and manufactures CAN bus interface modules in the UK. A module reads the digital messages on a vehicle's CAN network and turns them into simple outputs such as speed pulse, reverse, ignition and park brake, so installers and converters add equipment without cutting into the factory loom. Scorpion has built vehicle electronics in Chorley since 1973.
Speak to us about a CAN interface
Key facts
- Vehicle-fit modules: these stay fitted on the vehicle. They are a different job from the CAN analysers and test tools used in development labs.
- No splicing: the module connects to the vehicle network, not the factory loom, so the install stays clean and reversible.
- 14 interface guides cover the outputs installers reach for most.
- In-house: R&D, firmware and manufacturing, in Chorley, with IATF 16949 certification.
- OE capable: bespoke and line-fit CAN electronics are developed to automotive quality standards.
- Same factory as CANM8: the Chorley factory that makes our modules also manufactures CANM8 interfaces, and Intellitec MV's CAN KONTROL range is built there too.
Which signals can a CAN interface module provide?
The outputs below come off the vehicle network as simple signals. Each row links to a full guide.
| Interface | Output | Typical use |
|---|---|---|
| Speed pulse | A clean speed-pulse signal | Telematics, tachographs and speed-dependent equipment |
| Reverse trigger | A reverse-gear output | Aftermarket cameras and parking aids |
| Parking sensor | CAN-derived control | Retrofit parking-sensor systems |
| Ignition and accessory | Switched-live and accessory outputs | Add-on electronics that power up with the vehicle |
| Park brake | A handbrake signal | Screens and video-in-motion setups |
| Illumination | A panel-illumination output | Head units and displays that dim with the dash |
| Lighting triggers | High-beam, DRL and side-light detection | Light bars and auxiliary lighting |
| Beacon and work light | Low-amp triggers | Beacons, work lights and aux lighting |
| Multi-output | Several outputs from one connection | Speed, ignition, reverse, illumination and park brake together |
| RPM | An engine-speed signal | PTO and auxiliary equipment |
| Telematics takeoff | Speed and status feeds | Tracking and fleet devices |
| Commercial vehicle | Heavy-truck signal takeoffs | Side-scan and safety-camera control |
| Speed limiter | Real road speed off the CAN bus | Drive-by-wire speed limiting from Autokontrol |
| Runlock | Engine-running security | Keeping equipment powered with the key out |
Availability depends on the vehicle. Tell us the make, model and year and we'll confirm the right module.
Who buys CAN bus interface modules?
Anyone adding equipment to a modern vehicle without wanting to cut into its wiring.
- Converters and upfitters: signals and power for cameras, lighting, screens and equipment on van and truck conversions.
- Emergency vehicle builders: beacons, runlock, scene lighting and secure electronics for blue-light builds.
- Fleets and telematics installers: clean speed and status feeds for trackers and tachographs across a mixed fleet.
- OEMs and tier-one suppliers: line-fit CAN electronics developed and supplied to vehicle manufacturers.
Why a UK manufacturer matters for CAN interfaces
A module is only as good as the engineering behind it and the people you can call when a vehicle behaves unexpectedly.
- Own R&D and firmware: signal handling is written in-house.
- Own manufacturing: modules are made by the group that designs them, in the UK.
- Quality: IATF 16949 certified, with automotive quality standards, built up over 50-plus years in vehicle electronics.
- UK technical desk: installers get a team who know the hardware, plus fitting documentation.
- OEM and bespoke Custom and line-fit CAN electronics designed and built to your requirement.
- Power solutions Multiplexed power and control from group company Intellitec MV.
- CAN security X-Series reads the vehicle network to immobilise it and resists CAN injection.
- Speed limiting Drive-by-wire limiting from group company Autokontrol.
UK rules an installer checks before fitting a CAN interface
A CAN interface passes a signal and nothing more. It carries no approval and does not make a vehicle compliant, so the points below are what the installer must check against the official text for each job.
- Speed limiters: regulations 36A and 36B of the Road Vehicles (Construction and Use) Regulations 1986 cover buses and coaches and goods vehicles over 3.5 tonnes, for the dates, weights and exemptions set out there. A limiter must be sealed by an authorised sealer and kept in working order, so check it still works and its seal is intact after any fit that touches its speed source.
- Warning beacons and lamps: regulation 16 of the Road Vehicles Lighting Regulations 1989 restricts blue warning beacons and special warning lamps, with exceptions for emergency vehicles. Check the colour, use and authorisation of any lamp a CAN trigger will switch.
- Screens and condition: regulation 109 of the Construction and Use Regulations bars a television-type display the driver can see while driving, with exceptions such as navigation and views of the adjacent road. Regulation 100 requires the vehicle to be kept in a condition that is not a danger, so a park-brake lockout or similar feed must be tested and left working.
CAN KONTROL: the range behind the modules
The modules ship as CAN KONTROL lines, each named for its function, designed by our sister company Intellitec MV and built in our Chorley factory.
The i2CAN-4 carries one isolated CAN line up to 1 Mbps and four outputs of up to 900 mA. The i2CAN-8 handles two CAN peripherals and eight outputs, and CK-CV configurations add J1939 and FMS. Each module is programmed for the vehicle it ships to.
Moving over from another maker? The CANM8 alternative page matches CANM8 product names to the CAN KONTROL line that does the same job.
How to specify a CAN interface module
Three steps get you to the right module, whether it is one unit for a van conversion or a production run.
-
Tell us the vehicle and the signals
Give the make, model and year, and list the signals or outputs you need: speed, reverse, ignition, park brake, lighting or others.
-
Choose a standard module or discuss bespoke
Most jobs fit a standard interface. If yours needs a custom output, a multiplexed system or a line-fit programme, our engineers can develop it.
-
Fit it without cutting the loom
The module connects to the vehicle network, so the install is clean and reversible. Fitting documentation covers the wiring.
Frequently asked questions
Do you manufacture CAN bus interface modules in the UK?
Yes. Scorpion Automotive designs and manufactures CAN bus interface modules in Chorley, with in-house R&D and firmware. It has built vehicle electronics there since 1973.
What is a CAN bus interface module?
A module that reads the digital messages on a vehicle network and turns them into simple outputs, such as speed pulse, reverse, ignition or park brake, so you can add equipment without cutting into the factory wiring.
How is this different from a CAN analyser or test tool?
CAN analysers and test tools are used in development and diagnostics and usually stay on the bench or travel with an engineer. A vehicle-fit interface module stays fitted on the vehicle and feeds equipment permanently.
Do I have to splice into the vehicle loom?
No. The module connects to the vehicle network rather than the factory loom, which keeps the installation clean and reversible.
Which vehicles do your CAN modules support?
It depends on the vehicle and the signal you need. Tell us the make, model and year and we'll confirm the right module.
Can you develop a bespoke CAN solution or supply OE programmes?
Yes. Scorpion designs and manufactures CAN electronics to automotive quality standards, including line-fit OE programmes. Speak to us about your requirement.
Who manufactures CANM8 CAN bus interfaces?
CANM8 CAN bus interfaces come out of Scorpion Automotive's electronics factory in Chorley. CAN KONTROL, the Intellitec MV range, is made in the same factory to the same production standards, then configured to your exact vehicle by the group's own engineers.
Sources
- Road Vehicles (Construction and Use) Regulations 1986, regulation 36A (speed limiters, buses and coaches) (opens in a new tab) (accessed 10 October 2026)
- Road Vehicles (Construction and Use) Regulations 1986, regulation 36B (speed limiters, goods vehicles) (opens in a new tab) (accessed 10 October 2026)
- Road Vehicles (Construction and Use) Regulations 1986, regulation 109 (television sets) (opens in a new tab) (accessed 10 October 2026)
- Road Vehicles (Construction and Use) Regulations 1986, regulation 100 (maintenance and use so as not to be a danger) (opens in a new tab) (accessed 10 October 2026)
- Road Vehicles Lighting Regulations 1989, regulation 16 (blue warning beacons and special warning lamps) (opens in a new tab) (accessed 10 October 2026)
More on CAN bus
- CANM8 alternative CANM8 product names matched to CAN KONTROL lines.
- CAN bus integration The full capability hub, from signal to system.
- What is CAN bus? How a vehicle network works, in plain terms.
- CAN bus wiring basics Twisted pair, termination and connecting safely.
- CAN bus vs LIN, FlexRay and Ethernet Where each network is used in a vehicle.
- Installing telematics on CAN vehicles Taking speed and status off the network.
- OEM and bespoke electronics Design, prototype and build with the engineering team.
Talk to us about your CAN project
Tell us the vehicle, the signals or the system you need. Our engineers will take it from there.