CAN Bus Wiring Basics: Twisted Pairs, Termination and Bus Speed
By Alec J. Reviewed byJames M.
CAN bus wiring is a single twisted pair, CAN High and CAN Low, running past every module on the network with a 120 ohm resistor at each end. The twist rejects electrical noise, the resistors stop signals reflecting, and the bus speed decides how long the cable and its branches can be.
Key facts:
- Two wires: CAN High and CAN Low, twisted together, carrying a differential signal.
- Idle level: both wires sit at about 2.5 V when the bus is recessive.
- Termination: one 120 ohm resistor at each end of a high-speed bus.
- Speed vs length: the high-speed ISO 11898 figures are 1 Mbit/s over 40 m with up to 30 nodes.
- Stubs: a recommended maximum unterminated stub of 0.3 m at that speed.
How is a CAN bus wired?
High-speed CAN is a line, not a star. One twisted pair runs from one end of the network to the other, and each module joins it on a short branch called a stub.
- CAN High (CANH) and CAN Low (CANL) carry the data.
- Ground is shared through the vehicle’s own earth system.
- A resistor at each end terminates the line.
- Short stubs connect each control unit to the main pair.
Texas Instruments’ introduction to CAN describes the ISO 11898 topology as “a single line of twisted-pair cable”, terminated at both ends (Texas Instruments). The cable is specified as shielded or unshielded twisted pair with a 120 ohm characteristic impedance.
In a real vehicle the picture is busier. There may be several separate CAN networks, each its own line with its own pair of terminations, linked through a gateway module that passes selected messages between them. That’s why the signal you need may be on one network and not another.
Why are CAN bus wires twisted together?
Because the receiver doesn’t care about the voltage on either wire alone. It reads the difference between them.
When the bus is idle, or recessive, both wires are passively biased to about 2.5 V. When a module sends a dominant bit, CAN High rises by roughly 1 V to about 3.5 V and CAN Low falls by roughly 1 V to about 1.5 V, giving a differential signal of around 2 V (Texas Instruments).
Twisting the pair means any interference from ignition coils, alternators, motors or nearby looms lands on both wires almost equally. The difference between them barely changes, so the message survives. The currents in the two wires also run in opposite directions, which cancels much of the field the bus itself gives off.
Untwisting a long section during an install throws some of that protection away. Keep the twist right up to the connector.
What does CAN bus termination do?
Each end of a high-speed CAN line carries a 120 ohm resistor. It matches the cable’s characteristic impedance so a signal reaching the end of the wire is absorbed instead of bouncing back and corrupting the next bit.
Two points matter on a vehicle:
- Termination lives at the ends. It is usually inside the control units at each end of the network, not loose in the loom.
- Two in parallel read about 60 ohms. With the network powered down, measuring across CAN High and CAN Low should show the two 120 ohm resistors in parallel, which works out at 60 ohms.
TI’s guide also explains why the ISO standard avoids putting the termination resistor inside a node that might be removed: unplug that node and the bus loses its termination (Texas Instruments). For an installer, the lesson is the same in reverse. Never add a third resistor because a diagram looks bare, and never remove a module that may be holding one end of the bus.
How does bus speed affect cable length and stubs?
Faster bits leave less time for a signal to travel to the far end and settle. So the higher the bit rate, the shorter the bus has to be.
| Factor | High-speed CAN figure | Why it matters on a vehicle |
|---|---|---|
| Maximum signalling rate | 1 Mbit/s | Many vehicle networks run slower than this, which allows longer cables |
| Bus length at 1 Mbit/s | 40 m | Comfortably covers a car or van; long rigid vehicles need care |
| Nodes | Up to 30 | Each extra device loads the bus |
| Unterminated stub | 0.3 m recommended maximum | Long branches create reflections |
| Cable | Twisted pair, 120 ohm impedance | Untwisted or mismatched cable degrades the signal |
Figures from the high-speed ISO 11898 specifications as summarised by Texas Instruments.
The stub limit is the one installers break most often. Running a long flying lead from a module to the bus, then back again, turns a short branch into an aerial for reflections. Keep any connection to the network as short as you can, and don’t daisy-chain extra devices onto an existing stub.
Should you splice into CAN bus wiring?
As a rule, no.
Cutting into the pair, adding long tails, or loading the line with a device that isn’t built for it can corrupt messages for every module on that network. The symptoms rarely point back to the cause: warning lights, odd gauge behaviour or modules that drop offline intermittently.
The cleaner approach is to read the network through an interface built and tested for that vehicle. It joins the bus correctly and turns the messages you need into plain outputs. If you want the background on how CAN compares with the other networks in a vehicle, see our guide to CAN bus vs LIN, FlexRay and automotive Ethernet.
Scorpion CAN interfaces and clean wiring
Scorpion designs and manufactures CAN bus integration products in the UK. An ignition and accessory output gives add-on electronics a switched live that follows the vehicle, and a speed pulse interface provides a clean road-speed signal for telematics and speed-dependent kit. Both read the network instead of cutting into the factory loom, so the installation stays tidy and reversible.
Bosch introduced CAN in 1986 and ISO first standardised it in 1993 (CAN in Automation), and the wiring rules have changed very little since. Get the pair, the ends and the stubs right, and most of the network looks after itself.
Talk to us about CAN wiring on your build
Planning an install on a CAN vehicle and want the signal taken off cleanly? Our technical team can point you to the right interface.
- Speak to us about the vehicle and the outputs you need
- CAN bus integration for the full interface range
Frequently Asked Questions
What resistance should I measure across CAN High and CAN Low?
On a correctly terminated high-speed CAN bus, with the vehicle powered down, you should read about 60 ohms. That is the two 120 ohm end resistors in parallel. A reading near 120 ohms suggests one termination is missing.
What voltage is on CAN High and CAN Low?
When the bus is idle both wires sit at about 2.5 V. During a dominant bit CAN High rises to about 3.5 V and CAN Low falls to about 1.5 V, giving a differential of roughly 2 V.
Do I need to add a termination resistor when fitting an accessory?
Normally no. A vehicle network is already terminated at each end, usually inside control units. Adding another resistor lowers the bus resistance and can cause communication faults across the network.
How long can a CAN bus stub be?
For high-speed CAN at 1 Mbit/s the ISO 11898 figures recommend a maximum unterminated stub of 0.3 m. Shorter is better at any speed, because long branches reflect signals back onto the bus.
Does CAN bus wiring need to be shielded?
Not necessarily. The specification allows shielded or unshielded twisted pair with a 120 ohm characteristic impedance. Most vehicle networks rely on the twist and the differential signal to reject noise.
Speak to our team
Questions about vehicle security, tracking or fleet telematics? Our UK team will point you to the right product for your vehicle or fleet.
Related Products
View all products →- CAN bus
- wiring
- installers
- vehicle electronics
Alec J.
Software Engineer at Scorpion Automotive
Alec J., a Software Engineer at Scorpion Automotive in Chorley, covers CAN bus, vehicle electronics and electric vehicles.
Reviewed by James M., Technical Director at Scorpion Automotive