CAN Bus and Vehicle Electronics
How modern vehicles communicate over the CAN bus, and how security and tracking products read and use that data. It's for installers, engineers and technical buyers who want to fit cleanly without damaging the vehicle network. Scorpion's in-house R&D team covers CAN immobilisation, data integration and installation practice, so you can see what a product does on the vehicle.
-
CAN Bus and Vehicle Electronics 8 min readSpeed Pulse vs CAN Speed vs OBD Speed: Which Signal to Use
Which vehicle speed signal should you use? CAN speed read passively suits continuous feeds, a speed pulse suits pulse-only devices, and OBD polling suits occasional checks.
-
CAN Bus and Vehicle Electronics 4 min readWho Makes CANM8 Interfaces? Where They Are Built
Who makes CANM8 interfaces, and where? Scorpion Automotive's Chorley electronics factory manufactures them, and CAN KONTROL is built in the same factory.
-
CAN Bus and Vehicle Electronics 6 min read12V vs 24V Vehicle Electrics: Cars, Vans and HGVs Compared
Cars and most vans run 12V electrics, while heavy trucks, buses and much plant run 24V. Here's why, what changes in the wiring, and what it means when you fit accessories or security.
-
CAN Bus and Vehicle Electronics 6 min readIP Ratings for Automotive Electronics Explained
An IP rating tells you how well an enclosure keeps out dust and water. Here's how to read the code, what vehicle regulations ask for, and how to choose kit for the cabin, engine bay or chassis.
-
CAN Bus and Vehicle Electronics 7 min read5 Pin Relay vs 4 Pin Relay: Automotive Relays Explained
A 5 pin relay adds a normally closed output to the basic 4 pin switch, so one relay can change a circuit over instead of just switching it on. Here's how each works and which to fit.
-
CAN Bus and Vehicle Electronics 7 min readCAN Bus Fault Finding for Installers: Common Problems and Checks
A practical CAN bus fault finding routine for installers: the symptoms, the meter checks for termination and voltage, and the install mistakes that cause most network faults.
-
CAN Bus and Vehicle Electronics 7 min readCAN Bus vs LIN vs FlexRay vs Automotive Ethernet Compared
CAN, LIN, FlexRay and automotive Ethernet each do a different job inside a modern vehicle. Here's how they compare on speed, wiring and cost, and which one an installer is likely to meet.
-
CAN Bus and Vehicle Electronics 7 min readCAN Bus Wiring Basics: Twisted Pairs, Termination and Bus Speed
How CAN bus wiring works: why the two wires are twisted, why each end needs a 120 ohm resistor, and how bus speed limits cable length and stubs.
-
CAN Bus and Vehicle Electronics 7 min readDoes a CAN Interface Affect Your Vehicle Warranty?
Fitting a CAN interface doesn't automatically end a vehicle warranty, but a fault it causes may not be covered. Here's how the UK rules on warranties work and how to fit kit with the warranty in mind.
-
CAN Bus and Vehicle Electronics 6 min readDirect Vision Standard: What London HGV Operators Fit and Why
London's Direct Vision Standard sets a three-star minimum for HGVs over 12 tonnes. Lorries below it need the Progressive Safe System. Here's what that kit is and how it's triggered.
-
CAN Bus and Vehicle Electronics 6 min readFitting Accessories Without Cutting Wires or the Factory Loom
You can fit cameras, trackers, screens and lighting to a modern vehicle without cutting a single factory wire. Here's how installers do it and what to plan first.
-
CAN Bus and Vehicle Electronics 6 min readWhat Is a Micro Relay? Automotive Micro Relays Explained
An automotive micro relay is a smaller plug-in relay that does the same switching job as a full-size one in less space. Here's where micro relays are used, how they differ, and what to check before you fit one.
-
CAN Bus and Vehicle Electronics 5 min readVehicle Multiplexing: Multiplexed Wiring in Specialist Vehicles
Vehicle multiplexing sends control over a data network instead of a dedicated wire per switch. Here's how multiplexed wiring works on specialist vehicles and when it beats a conventional loom.
-
CAN Bus and Vehicle Electronics 5 min readVehicle Power Distribution Modules: When You Need One
A power distribution module replaces banks of relays and fuses with one controlled, monitored unit. Here's when a specialist vehicle outgrows conventional wiring and needs one.
-
CAN Bus and Vehicle Electronics 6 min readTelematics Installation on CAN Bus Vehicles: Ignition and Speed
A tracker is only as accurate as the ignition and speed signals it receives. Here's how to get both right when installing telematics on a CAN bus vehicle.
-
CAN Bus and Vehicle Electronics 6 min readVan Auxiliary Battery Guide: Avoiding Flat Batteries
Every tracker, camera, inverter and light added to a van draws on the battery. Here's how auxiliary loads cause flat batteries, when a van auxiliary battery makes sense, and how to wire it properly.
-
CAN Bus and Vehicle Electronics 6 min readVehicle Converter Electronics: CAN Integration for Converters
Converters add lighting, cameras, power and control to vehicles that were never built for them. Here's what vehicle converter electronics need from the base vehicle's CAN network, and how to plan it.
-
CAN Bus and Vehicle Electronics 6 min readWhat Is CAN Bus? A Plain-English Guide for Installers
CAN bus is the two-wire network that lets a vehicle's control units share data. Here's how it works, why it replaced point-to-point wiring, and what it means when you fit aftermarket kit.
-
CAN Bus and Vehicle Electronics 6 min readCAN Bus Interface: Why Modern Vehicles Need One for Fitting
Modern vehicles carry ignition, speed and reverse as network messages, not wires. Here's why a CAN bus interface is now the standard way to fit aftermarket kit.