Van Auxiliary Battery Guide: Avoiding Flat Batteries
By Alec J. Reviewed byJames M.
A van auxiliary battery is a second battery that runs added equipment, such as lights, inverters, fridges and tools, so the starter battery stays charged for the engine. If your van keeps going flat, the usual cause is auxiliary electrical load drawing on a single battery faster than driving can put the charge back.
Key facts:
- Every added device draws current, and some draw it with the engine off.
- Small standby loads add up over a weekend or a bank holiday.
- A second battery separates the work load from the engine-starting job.
- Split charge connects the batteries while the engine runs; a DC-DC charger regulates the charge into the second battery.
- Switching with the ignition stops accessories running when the van is parked.
Why does my van battery keep going flat?
Most flat van batteries aren’t faulty batteries. They’re a mismatch between what the van uses and what it puts back.
A standard van leaves the factory with a battery sized for starting and for its own electronics. Then the conversion starts. Racking lights, inverters, a fridge, a camera system, a tracker and an alarm all get added, often by different people at different times, and nobody adds up the total.
Two patterns cause most problems:
- Loads left running with the engine off. A light, an inverter or a fridge on a permanent feed keeps drawing until the battery can’t start the engine.
- Short journeys with heavy use. A multi-drop van that stops every few minutes, with doors open and lights on, may never run long enough to recharge.
Standby current from security and telematics is normal and expected. It only becomes a problem when it’s stacked on top of other permanent loads, or when the van is parked for long spells.
How do you work out the auxiliary electrical load?
Start with a list, not a guess.
- Write down every added device and whether it’s on a permanent or ignition-switched feed.
- Find its current draw from the manufacturer’s data, running and on standby.
- Estimate the hours each one runs with the engine off.
- Multiply current by hours to get amp-hours, then total them.
Compare that total with the usable capacity of the battery, not its label rating. Lead-acid batteries don’t like deep discharge, so only part of the rated capacity is comfortably usable day after day.
If the engine-off total is a meaningful share of what the battery can give, the van needs either less engine-off load or a second battery.
When does a van need an auxiliary battery?
Not every van does. A light-duty van with a tracker, an alarm and a couple of LED work lights on an ignition feed usually manages on one battery.
A van auxiliary battery makes sense when:
| If your van has… | Start with… |
|---|---|
| Lights and accessories that only run while driving | An ignition-switched feed on the existing battery |
| Equipment that runs for hours with the engine off | A second battery with a proper charging link |
| An inverter for mains tools on site | A second battery sized for the inverter load |
| Refrigeration or heating while parked | A second battery and load monitoring |
| Heavy, specialist or emergency equipment | An engineered power management system |
The table is a starting point. A specialist vehicle with serious loads, such as an ambulance or a workshop van, is better served by a designed system than by a battery added on the bench.
Split charge or DC-DC charger?
A second battery needs charging from the alternator without letting it drain the starter battery. There are two common approaches.
Split charge relays and isolators connect the two batteries while the engine runs and separate them when it stops. Battery isolators let one charging source supply more than one battery while preventing a weak battery from draining a strong one, and they’re widely used on vans, motorhomes, boats and trucks (Battery isolator). Diode-based isolators add some voltage drop to the circuit.
DC-DC chargers take power from the vehicle side and regulate the voltage and charging stages into the auxiliary battery. That matters on newer vehicles, where the alternator output isn’t fixed. On many modern engines, voltage regulation is handled by the engine control unit, which adjusts the alternator voltage according to factors such as temperature and engine load (Alternator (automotive)). A charger that regulates its own output isn’t relying on whatever voltage the alternator happens to be giving.
Before fitting either, check the vehicle manufacturer’s body builder or conversion guidance for approved connection points. Many modern vans monitor the battery, and a connection in the wrong place can confuse that monitoring.
How do you stop accessories draining the battery?
Most of the fix is in how equipment is switched.
- Use an ignition-switched feed for anything that only needs to run while the van is in use.
- Take that feed cleanly. On CAN vehicles, an ignition and accessory output gives a switched live from the vehicle network without cutting into the factory loom.
- Fuse every circuit at the supply end.
- Keep permanent feeds for equipment that must work with the engine off, such as security and tracking.
- Fit low-voltage cut-offs to heavy loads, so they shut down before the starter battery is drained.
Tracking units belong on a permanent supply, because they need to report when the van is parked. Our guide to telematics installs on CAN vehicles covers how to take ignition and speed signals properly for them.
CAN feeds and power from Scorpion
Scorpion makes the CAN interfaces that give converters and installers clean switched feeds off the vehicle network, with no cutting into the loom. See the full range on our CAN bus integration page.
For vehicles carrying serious electrical loads, our power solutions page covers power distribution, multiplexed control and battery management for specialist vehicles, built by Intellitec MV in the UK.
Talk to us about your van conversion loads
Converting vans and battling flat batteries? Tell us the vehicle and the equipment, and we’ll help you plan the feeds.
- Speak to us about your van build
- Ignition and accessory output for a clean switched feed
Frequently Asked Questions
What is a van auxiliary battery?
It’s a second battery fitted to run added equipment, such as lights, inverters, fridges or tools, separately from the starter battery. A charging link from the alternator keeps it topped up while driving, and the starter battery stays reserved for the engine.
Why does my van battery go flat overnight?
Usually because something added to the van is drawing current with the engine off: a light, inverter, fridge or accessory on a permanent feed. Check what’s wired to permanent supplies and move anything that doesn’t need to run while parked onto an ignition-switched feed.
Is a split charge relay or a DC-DC charger better?
A split charge relay simply connects the batteries while the engine runs. A DC-DC charger regulates the charge into the second battery, which suits newer vehicles where the alternator voltage varies. Check the vehicle manufacturer’s guidance before choosing.
Will a tracker or alarm flatten my van battery?
A correctly installed tracker or alarm has a small standby draw that a healthy battery handles easily. Problems arise when that draw is added to other permanent loads, or when the van is parked for long periods on a weak battery.
How do I power accessories only when the ignition is on?
Take a switched live that follows the ignition. On modern vans the cleanest way is a CAN ignition and accessory output, which reads the vehicle network and provides the feed without cutting into the factory wiring.
Speak to our team
Questions about vehicle security, tracking or fleet telematics? Our UK team will point you to the right product for your vehicle or fleet.
Related Products
View all products →- vans
- vehicle electronics
- conversions
- auto electrics
Alec J.
Software Engineer at Scorpion Automotive
Alec J., a Software Engineer at Scorpion Automotive in Chorley, covers CAN bus, vehicle electronics and electric vehicles.
Reviewed by James M., Technical Director at Scorpion Automotive