Skip to main content
English
CAN Bus and Vehicle Electronics

5 Pin Relay vs 4 Pin Relay: Automotive Relays Explained

7 min read

By Alec J. Reviewed byJames M.

5 Pin Relay vs 4 Pin Relay: Automotive Relays Explained: Scorpion Automotive guide illustration with a power and relay icon

A 5 pin relay is a changeover relay: it has the same coil and switched contact as a 4 pin relay, plus a fifth pin that stays connected while the relay is off. A 4 pin relay only switches a circuit on. A 5 pin relay can swap a feed between two circuits.

The short version:

  • Pins 85 and 86 are the coil on both types. A small current here moves the switch.
  • Pin 30 is the feed into the switch contact.
  • Pin 87 is the normally open output, live only when the coil is energised.
  • Pin 87a is the extra pin on a 5 pin relay: normally closed, live when the coil is off.
  • A 5 pin relay wired without 87a behaves exactly like a 4 pin relay.

What does a relay do in a vehicle?

A relay lets a small current switch a large one. A dashboard switch, an alarm output or a CAN interface can only handle a few milliamps or a fraction of an amp. Spotlights, horns, fuel pumps and starter circuits need far more than that.

So the small signal energises the relay coil, the coil pulls a contact across, and the heavy current flows through the relay instead of through the switch.

That gives you three practical wins:

  1. Thin control wiring. Only the coil circuit runs back to the switch or module.
  2. Short heavy wiring. The high-current path can run directly from a fused supply to the load.
  3. Protected electronics. Modules with low-current outputs can drive loads they could never carry themselves.

Most cars and vans use plug-in relays in a fuse and relay box, and aftermarket installers add their own for accessories, alarms and immobilisers.

What do the pins on a 5 pin relay mean?

Automotive relay terminals follow the German DIN 72552 numbering, which also gives us terminal 30 for a permanent battery feed and 15 for an ignition-switched feed (DIN 72552). On the common plug-in pattern you’ll find on most cars, the pins are used like this:

Pin4 pin relay5 pin relayWhat it connects to
85CoilCoilUsually earth, or the switched side of a module output
86CoilCoilUsually the switched trigger feed
30Contact feedContact feedFused supply for the load
87Normally openNormally openThe load you want switched on
87aNot fittedNormally closedA second load that runs while the relay is off

Always check the diagram printed on the relay case. Some relays swap the coil polarity or include extra components, and the printed diagram is the one that counts.

4 pin vs 5 pin relay: what is the difference?

The difference is the contact type. In relay terms, a 4 pin automotive relay has a single normally open contact, called SPST or Form A. A 5 pin relay has a changeover contact, called SPDT or Form C (Relay).

Normally open means the circuit is broken until the coil is energised. Normally closed means the circuit is made until the coil is energised, then it breaks.

On a 5 pin relay, pin 30 is always connected to one of the two outputs:

  • Coil off: 30 connects to 87a.
  • Coil on: 30 connects to 87.

That’s why a 5 pin relay is so useful to installers. It can do everything a 4 pin relay does, and it can also cut a circuit when triggered, or switch a feed from one device to another.

When do you need a 5 pin relay?

Fit a 4 pin relay when all you need is “on when triggered”. Fit a 5 pin relay when the job needs the normally closed side.

Typical 5 pin jobs:

  • Immobiliser circuits. A circuit can be routed through 30 and 87a so it works normally until the relay is triggered, then breaks. Which circuit to interrupt, and how, depends on the product’s own fitting instructions.
  • Changeover switching. Swap one feed between two lamps, two horns or two signals, so only one is ever live.
  • Fail-safe logic. Keep something running unless a signal tells it to stop.
  • Polarity reversal. Two changeover relays together can reverse a small motor, such as a door lock actuator.

A 5 pin relay is also the more flexible spare to carry. If 87a isn’t wired, it simply works as a 4 pin relay.

How do you wire a 5 pin relay safely?

The wiring is simple. The care is in the details.

  1. Fuse the feed to pin 30 close to the supply, rated for the load and the cable.
  2. Size the cable on the 30 and 87 paths for the load current, not the coil current.
  3. Connect the coil across 85 and 86, matching any polarity marked on the case.
  4. Use 87 for the switched load, and 87a only if you need the normally closed function.
  5. Check the coil voltage. A 12V relay belongs on a 12V system, and a 24V relay on a 24V truck system. Our guide to 12V vs 24V vehicle electrics covers why the two don’t mix.

A relay coil is an inductor. When it switches off, the collapsing magnetic field produces a voltage spike, which is why many relays carry a flyback diode or resistor across the coil to protect the electronics driving it (Relay). If you’re driving the coil from a module output, a suppressed relay is the safer choice. Diode-suppressed relays have a fixed coil polarity, so wire them the right way round.

Relays, interfaces and modern vehicles

On older vehicles, the trigger for a relay was a simple wire: the reverse lamp feed, the ignition live, the sidelight circuit. On many modern vehicles those signals live on the CAN bus as data messages rather than as dedicated wires.

That’s where a CAN interface comes in. It reads the message and gives a clean low-current output, and a relay then does the heavy switching. Interface for the signal, relay for the load: it’s a common pairing on conversions, fleet installs and lighting jobs.

Scorpion and relay-switched circuits

Scorpion builds vehicle electronics in the UK and sells its own relay to the trade. The Scorpion 5-pin Micro relay is a compact, waterproof relay module that you can use in place of a traditional 5-pin relay in most automotive applications.

Alongside it sit our CAN interfaces and the security products in our vehicle security hardware range, so the signal, the switching and the security on an install can come from one UK manufacturer.

Talk to us about relay and interface wiring

Need a relay for a production run, or a signal you can’t find on the vehicle? Our UK technical team can talk it through.

Frequently Asked Questions

What is the difference between a 4 pin and a 5 pin relay?

A 4 pin relay has one normally open contact, so it only switches a circuit on. A 5 pin relay adds pin 87a, a normally closed contact, so it can switch a feed between two outputs or break a circuit when triggered.

Can I use a 5 pin relay instead of a 4 pin relay?

Yes, in most cases. Leave pin 87a unconnected and a 5 pin relay works like a 4 pin relay. Check the coil voltage, current rating and pin layout match the original before swapping it in.

What is pin 87a on a relay?

Pin 87a is the normally closed output on a 5 pin changeover relay. It is connected to pin 30 while the coil is off, and disconnects when the coil is energised and the contact moves across to pin 87.

Which pins are the coil on an automotive relay?

On the standard automotive pattern, pins 85 and 86 are the coil. Feed one and earth the other to energise it. If the relay has a suppression diode, the coil has a polarity, so follow the diagram on the case.

Why does a relay need a diode across the coil?

When the coil switches off, its collapsing magnetic field creates a voltage spike. A diode or resistor across the coil absorbs that spike, protecting the switch, module or interface that drives the relay.

Speak to our team

Questions about vehicle security, tracking or fleet telematics? Our UK team will point you to the right product for your vehicle or fleet.

View all products →
Tags:
  • relays
  • vehicle electronics
  • installers
  • auto electrics
Scorpion Automotive

Alec J.

Software Engineer at Scorpion Automotive

Alec J., a Software Engineer at Scorpion Automotive in Chorley, covers CAN bus, vehicle electronics and electric vehicles.

Reviewed by James M., Technical Director at Scorpion Automotive