Skip to main content
English
CAN Bus and Vehicle Electronics

12V vs 24V Vehicle Electrics: Cars, Vans and HGVs Compared

6 min read

By Alec J. Reviewed byJames M.

Large mining dump trucks hauling ore along an open-cast site road

The difference between 12V vs 24V vehicle electrics comes down to size. Cars and most vans run a 12V system from one battery. Heavy trucks, buses, coaches and much construction plant run 24V, usually from two 12V batteries in series, because doubling the voltage halves the current for the same power.

Key facts:

  • 12V nominal comes from six lead-acid cells of about 2.1V each, roughly 12.6V when fully charged.
  • 24V systems on heavy vehicles normally use two 12V batteries wired in series.
  • Running voltage is higher than nominal: an alternator holds a 12V system at about 13.5V to 14.5V.
  • Half the current for the same power is the main reason big vehicles use 24V.
  • Not interchangeable: 12V equipment on a 24V supply is likely to be damaged.

Why are cars and vans 12V?

The 12V standard is a historical settlement. Cars ran 6V electrics until the mid-1950s, and the switch to 12V came when bigger, higher-compression engines needed more power to start. Some models held out longer: the Volkswagen Beetle moved over in the mid-1960s (Automotive battery).

A nominal 12V battery is six cells in series. Each cell gives about 2.1V, so a healthy, fully charged battery reads roughly 12.6V at rest. With the engine running, the alternator lifts the system to somewhere between 13.5V and 14.5V to charge it (Automotive battery).

For a car or light van, 12V is plenty. Starter motors, lighting and electronics are all sized around it, and almost every accessory on the market is built for it.

Why do trucks, buses and plant use 24V?

It’s about current. Electrical power is voltage multiplied by current, so a 24V system delivers the same power as a 12V system with half the current.

That matters on big vehicles in four ways:

  1. Starting. A large diesel needs a lot of cranking power. At 24V, the starter draws far less current for the same output.
  2. Cable size. Lower current means thinner cable for the same job, which saves weight and cost on a long chassis.
  3. Voltage drop. On a 12m trailer run or a long bus, resistance in the cable eats voltage. Halving the current halves the loss.
  4. Heat. Less current through connectors and switches means less heat in them.

Heavy vehicles get there by putting two 12V batteries in series, or series-parallel groups of batteries, to make 24V (Automotive battery).

12V vs 24V vehicle systems compared

CarsVans and light commercialsHGVs, buses, coachesConstruction and agricultural plant
Typical system12V12V24VOften 24V on larger machines, 12V on smaller ones
Battery setupOne 12V batteryOne 12V battery, sometimes a second for auxiliariesTwo 12V batteries in seriesVaries by machine size
What to check before fittingStandby drain, CAN signalsAuxiliary loads, conversion wiringSupply voltage, CAN messagesSupply voltage, sealing, vibration

The table is a rule of thumb, not a guarantee. Large vans, motorhome bases and some specialist builds sit on the boundary, so always measure before you fit.

What changes when you fit kit to a 24V vehicle?

Almost everything you plug in has to be rated for the supply. A 12V relay coil, lamp or module wired straight to 24V sees double its rated voltage, which usually ends badly.

Before fitting, installers check:

  • Equipment rating. Is the product rated for 24V, or for a 12V and 24V range?
  • Relay coils. A 24V system needs 24V coils. Our guide to automotive relays covers the pins themselves.
  • Converters. 12V-only accessories on a truck need a proper 24V to 12V converter, sized for the load, rather than a tap off one battery.
  • Signals. Many truck signals live on the CAN network. A commercial vehicle CAN interface reads them without cutting into the loom.

Never tap 12V from one battery of a series pair. It unbalances the batteries, so one ends up overcharged and the other undercharged.

Does the voltage affect auxiliary loads and flat batteries?

Yes, though the principles are the same on both. A vehicle that sits with trackers, alarms, cameras or refrigeration running still drains its battery. The difference on 24V is that you’re managing two batteries that must stay balanced.

On 12V vans, auxiliary loads are often the bigger worry, because conversions add so much equipment to a single battery. We cover that in detail in auxiliary loads on vans.

Scorpion kit for 12V and 24V vehicles

Scorpion has built vehicle electronics in the UK since 1973, and the voltage question comes up on every commercial job. Our range of vehicle alarms and immobilisers covers cars and vans, while plant and agricultural security is built for machines that work in harsher conditions. For trucks, our guide to HGV alarms and immobilisers for 24V covers security on 24V systems.

For trucks and buses, our CAN interfaces take speed, reverse, indicator and ignition signals off the vehicle network so cameras, beacons and body equipment switch on the right logic. If the job needs something off the shelf can’t do, we can develop it.

Talk to us about a mixed 12V and 24V fleet

Fitting to a mixed fleet of 12V and 24V vehicles? Tell us what you’re running and we’ll point you to the right kit.

Frequently Asked Questions

Is my vehicle 12V or 24V?

Cars and most vans are 12V. HGVs, buses, coaches and many larger plant machines are 24V. If the vehicle has two large batteries linked in series, it’s almost certainly 24V. Measure across the battery bank with a meter to be sure.

Why do trucks use 24V instead of 12V?

A 24V system delivers the same power with half the current. That makes heavy diesel starting easier, allows thinner cables over a long chassis and cuts voltage drop. It’s achieved with two 12V batteries wired in series.

Can I use 12V equipment on a 24V vehicle?

Not directly. Connecting 12V equipment to a 24V supply is likely to damage it. Use equipment rated for 24V, or fit a correctly sized 24V to 12V converter for the accessory.

Can I take 12V from one battery on a 24V truck?

It isn’t recommended. Drawing from one battery of a series pair unbalances them, so one battery ends up overcharged and the other undercharged, shortening the life of both. A converter is the proper way.

What voltage should a 12V vehicle battery read?

A fully charged 12V lead-acid battery reads about 12.6V at rest. With the engine running, the charging system typically holds it between about 13.5V and 14.5V.

Speak to our team

Questions about vehicle security, tracking or fleet telematics? Our UK team will point you to the right product for your vehicle or fleet.

View all products →
Tags:
  • vehicle electronics
  • HGV
  • installers
  • auto electrics
Scorpion Automotive

Alec J.

Software Engineer at Scorpion Automotive

Alec J., a Software Engineer at Scorpion Automotive in Chorley, covers CAN bus, vehicle electronics and electric vehicles.

Reviewed by James M., Technical Director at Scorpion Automotive