Does a CAN Interface Affect Your Vehicle Warranty?
By Alec J. Reviewed byJames M.
A CAN interface doesn’t automatically affect your vehicle warranty. Under UK competition guidance, a manufacturer can’t make the warranty conditional on using only its own network for work the warranty doesn’t cover, but it can refuse a claim where a third-party part or poor workmanship caused the fault.
The short version:
- No blanket void: fitting aftermarket kit is not, on its own, a reason to cancel a whole warranty.
- Cause matters: a claim can be refused if the fault is causally linked to a third-party part or to work done badly.
- The rules: the UK Motor Vehicle Block Exemption Order applies from 1 June 2023, with CMA guidance alongside it.
- Install quality counts: a plug-in CAN connection with no cut wires is far easier to stand behind than a spliced loom.
- Check first: read the warranty terms and ask the manufacturer or dealer before you fit.
What does the law say about warranties and aftermarket kit?
The Competition and Markets Authority (CMA) published its Guidance on Motor Vehicle Agreements on 5 June 2023, alongside the Motor Vehicle Block Exemption Order (MVBEO), which applies from 1 June 2023.
Two passages matter here:
- Paragraph 5.36: a warranty made conditional on having repair and maintenance work it doesn’t cover carried out only by the authorised network may breach competition law.
- Paragraph 5.37: the same goes for warranty conditions that demand manufacturer-branded parts for replacements the warranty doesn’t cover. But the guidance is clear that a manufacturer, or any other warranty provider, can legitimately refuse a claim that is causally linked to a repair done incorrectly or to the failure of a third-party part.
The guidance also says terms that clearly state your right to use an independent repairer without losing the warranty are unlikely to raise competition concerns.
It’s written about repair, maintenance and spare parts. It doesn’t name accessories such as trackers, cameras or CAN interfaces. So treat it as the framework, not a ruling on your exact situation, and check your own warranty terms.
Does fitting a CAN interface void the warranty?
Not by itself. What decides a claim is the link between the fault and the work.
Say a new van develops a gearbox fault six months after a tracker went in. The gearbox claim has nothing to do with the tracker, so the tracker is no reason to refuse it. Now say a body control module fails and the fitter had spliced into the data wires next to it. That’s a very different conversation, and the warranty provider may well point at the install.
That’s why the question “does a CAN interface void the warranty” has the answer “it depends what goes wrong, and why”.
| Situation | Likely warranty position |
|---|---|
| Fault unrelated to the fitted kit | Kit is not a reason to refuse the claim |
| Fault caused by a faulty third-party part | Provider may refuse that claim |
| Fault caused by poor installation | Provider may refuse that claim |
| Warranty says “authorised network only” for non-warranty work | Condition may breach competition law (CMA 5.36) |
| Extended or dealer warranty with extra conditions | Read the terms: they still apply as written |
How do you fit a CAN interface with the warranty in mind?
The best protection is an install nobody can fault. A few habits make that much easier.
- Read the terms first. Manufacturer, extended and lease warranties can carry different conditions.
- Don’t cut data wires. On a CAN vehicle many signals only exist as messages, as our guide to what CAN bus is explains. Splicing into the network is where faults start.
- Use a proper interface. A CAN interface reads the messages and provides clean outputs, such as an ignition and accessory output, with no cutting into the factory loom.
- Fuse and route properly. Protect every new feed and keep wiring away from moving parts and heat.
- Keep records. Photos, the product used and the connection points help if a question ever comes up.
- Use a trained fitter. Workmanship is one of the two grounds the CMA guidance gives for refusing a claim.
Why does a clean CAN install matter so much?
Because it’s reversible and easy to show.
A plug-in or non-invasive network connection leaves the factory loom as it was built. If the vehicle goes back to the dealer with a fault, the technician can see exactly what was fitted and where. If needed, the kit can come out and the vehicle returns to standard.
Compare that with a loom that’s been cut, soldered and taped in several places. Even when the work was good, it’s harder to prove, and every joint is a possible point of failure. On a modern vehicle, loading a circuit the body computer monitors can also set fault codes or warning lights.
So the warranty case and the engineering case point the same way.
What should fleets and lease companies check?
Fleet and lease vehicles add another layer: the vehicle often isn’t yours to modify freely.
- Lease agreement: many contracts require permission before fitting equipment and expect the vehicle back in standard condition.
- Manufacturer warranty: still runs alongside the lease, with its own terms.
- Body builder or converter warranty: may cover the conversion separately.
- Telematics and cameras: often fitted across a whole fleet, so one install method repeated well is worth more than a dozen improvised ones.
If you’re unsure, ask the leasing company or the manufacturer in writing before the rollout starts. A short email now saves a long argument later.
Scorpion and warranty-safe CAN fitting
Scorpion designs and manufactures CAN electronics in the UK. Our CAN bus integration range takes speed, ignition, reverse, park-brake, lighting and other signals off the vehicle network and provides clean outputs, with no cutting into the factory loom. Each interface reads the vehicle’s own messages in configuration, so the install stays tidy and reversible.
For trade fitters, our approved installer route covers product and fitment training.
Talk to us about CAN interfaces for fleets and leases
Fitting kit to vehicles still under warranty? Tell us the make, model and the signals you need, and our engineers will suggest a clean way to take them off the network.
- Speak to us about the vehicle and the install
- CAN bus integration for the full range of interfaces
Frequently Asked Questions
Does a CAN bus interface void my car warranty?
Not automatically. UK competition guidance says a warranty provider can refuse a claim when the fault is causally linked to a third-party part or to incorrect work. A fault with no link to the interface is not a reason to refuse that claim. Always check your own warranty terms.
Will fitting a tracker void my warranty?
A correctly fitted tracker should not, by itself, end a manufacturer warranty. If a fault is caused by the tracker or by how it was wired in, that particular claim may be refused. A non-invasive connection and a trained fitter reduce that risk considerably.
What is the Motor Vehicle Block Exemption Order?
It is the UK order covering competition law for agreements in the motor vehicle sector, applying from 1 June 2023. The CMA published guidance alongside it, including how warranty conditions involving authorised repairers and branded parts are assessed.
Can a dealer insist I only use their workshop to keep the warranty?
For repair and maintenance work the warranty doesn’t cover, CMA guidance says making the warranty conditional on using only the authorised network may breach competition law. Work done under the warranty itself is a different matter. Check the exact wording of your terms.
How do I protect my warranty when fitting accessories?
Read the warranty terms, avoid cutting into data wires, use a proper CAN interface, fuse and route every feed, keep photos and records, and use a trained fitter. If in doubt, ask the manufacturer or leasing company in writing before you start.
Speak to our team
Questions about vehicle security, tracking or fleet telematics? Our UK team will point you to the right product for your vehicle or fleet.
Related Products
View all products →- CAN bus
- vehicle warranty
- installers
- aftermarket fitting
Alec J.
Software Engineer at Scorpion Automotive
Alec J., a Software Engineer at Scorpion Automotive in Chorley, covers CAN bus, vehicle electronics and electric vehicles.
Reviewed by James M., Technical Director at Scorpion Automotive