Skip to main content
English
CAN Bus and Vehicle Electronics

CAN Bus Fault Finding for Installers: Common Problems and Checks

7 min read

By Alec J. Reviewed byJames M.

CAN Bus Fault Finding for Installers: Common Problems and Checks: Scorpion Automotive guide illustration with a CAN bus wiring icon

CAN bus fault finding starts with the last thing that changed on the vehicle. Most network faults after an install come from a disturbed connector, a splice into the data pair, a long stub or a missing termination, and two meter checks find most of them: resistance across the pair with power off, then voltage with power on.

Key facts:

  • Symptoms spread: one bad connection can upset every module on that network.
  • Powered down, a healthy high-speed bus reads about 60 ohms between CAN High and CAN Low.
  • Idle voltage on both wires is about 2.5 V, with CAN High going up and CAN Low going down during traffic.
  • Error frames make modules discard and resend bad messages, so faults often show as intermittent.
  • Undo first: disconnecting the newly fitted device is the fastest test there is.

What are the signs of a CAN bus fault?

CAN faults rarely announce themselves as “network fault”. They show up as odd behaviour in modules that seem unrelated to the job you’ve just done.

  • Clusters of warning lights appearing together after an install.
  • Gauges dropping out or flickering, such as the speedometer or fuel gauge.
  • Lost communication codes when a diagnostic tool scans the vehicle.
  • Intermittent faults that come and go with temperature, vibration or door movement.
  • Accessories misbehaving: a camera that won’t trigger, or a tracker that never sees ignition.

The reason is the way CAN handles errors. When a module detects a corrupted message it sends an error frame, every other node rejects that message, and the transmitter sends it again. Error counters in each controller stop one faulty node from tying up the bus forever (Texas Instruments). So a marginal connection produces a stream of retries and dropped messages rather than one clean failure.

Where should you start CAN bus fault finding?

Start with what you touched. A routine that works on most vehicles:

  1. Note the symptoms and read the codes with a diagnostic tool, before you clear anything.
  2. Disconnect the device you fitted. If the fault clears, the device, its connection or its setup is the cause.
  3. Inspect every connector you opened for pushed-back pins, bent terminals or a plug that hasn’t latched.
  4. Check any splice or tap on the data pair. Better still, remove it.
  5. Take the meter readings below.
  6. Rule out power and earth at the modules involved. A weak supply or poor ground can look like a network fault.

That order matters. Ten minutes of undoing your own work usually beats an hour of chasing codes in modules you never went near.

How do you test a CAN bus with a multimeter?

A meter won’t show you the data, but it will tell you whether the physical bus is healthy.

Resistance check, power off

Disconnect the battery or let the vehicle’s networks go fully to sleep, then measure between CAN High and CAN Low at an accessible point.

ReadingLikely meaning
About 60 ohmsBoth 120 ohm end resistors present, in parallel
About 120 ohmsOne end termination missing or one leg of the bus open
Well under 60 ohmsAn extra resistor fitted, or the two wires shorted together
Open circuitBoth ends lost, or you are not on the bus you think you are

The 60 ohm figure follows from the ISO 11898 layout of a 120 ohm resistor at each end of the line (Texas Instruments).

Voltage check, power on

With the network awake, measure each wire to a good ground. At rest both sit at about 2.5 V. When a dominant bit is sent, CAN High rises to about 3.5 V and CAN Low falls to about 1.5 V (Texas Instruments). A meter averages the traffic, so you’d expect CAN High a little above 2.5 V and CAN Low a little below it.

A wire pulled to 0 V points to a short to ground. A wire sitting near battery voltage points to a short to a supply. Both wires reading the same value with the network busy suggests they’re shorted together.

Which installation mistakes cause CAN faults?

Most come back to the wiring rules covered in our guide to CAN bus wiring basics.

  • Splicing into the data pair. Every joint adds resistance and a chance of corrosion. Scotch locks and pinch-on connectors are the worst offenders.
  • Long stubs. The high-speed CAN figures recommend an unterminated stub of no more than 0.3 m at 1 Mbit/s. A long flying lead to a device works as an aerial for reflections.
  • Untwisting the pair over a long run, which weakens noise rejection.
  • Adding a termination resistor because a diagram looked incomplete. A third resistor drops the bus resistance below 60 ohms.
  • Unplugging a module that holds one end of the bus, leaving the network with only one termination.
  • Cheap or generic interfaces that load the bus or send messages it doesn’t expect.

How do you avoid CAN faults on the next install?

Prevention is mostly about not touching the data pair at all.

  1. Use a platform-specific interface that joins the network correctly instead of tapping a wire.
  2. Keep connections short and keep the twist right up to the connector.
  3. Use proper connectors and support the loom so vibration can’t work them loose.
  4. Record a baseline: scan for codes before you start, so you know which faults were already there.
  5. Test with the vehicle fully awake and then asleep, since some faults only appear as networks wake up.

Scorpion CAN interfaces and fault support

Scorpion’s CAN bus integration range reads the vehicle network through a single, clean connection and provides plain outputs for the accessory. A multi-output interface gives speed, ignition, reverse, illumination and park brake from one connection, which means fewer joins and fewer places for a fault to hide. Every interface is built for the platform it sits on, with coverage kept current by in-house firmware.

For fitters who want product and fitment training and a UK technical desk behind them, our approved installer programme is the route in.

Talk to us about a CAN fault on a job

Chasing a CAN fault on one of our products, or planning an install and want to avoid one? Our technical team will talk it through with the vehicle in front of you.

Frequently Asked Questions

How do I check if a CAN bus is working?

With the vehicle powered down, measure about 60 ohms between CAN High and CAN Low. With it awake, each wire should sit around 2.5 V, CAN High slightly above and CAN Low slightly below while messages are flowing. A diagnostic scan confirms modules are talking.

What does 120 ohms across CAN High and CAN Low mean?

It usually means one of the two 120 ohm end terminations is missing, or one leg of the bus is open. Check connectors at the modules at each end of the network, and any module that has been removed or unplugged.

Can a tracker or camera install cause a CAN bus fault?

Yes, if the install disturbs the network. Splices into the data pair, long stubs, loose connectors or a device that loads the bus can all upset messages. Disconnecting the new device is the quickest way to prove it.

Why do CAN bus faults come and go?

Many are caused by marginal connections that change with heat, vibration or movement. Because CAN modules resend corrupted messages, a weak joint produces intermittent dropouts rather than a constant failure.

Should I add a termination resistor to fix a CAN fault?

Only if you have proved an end termination is missing and you are restoring it to its correct place. Adding an extra resistor to a healthy bus lowers its resistance below 60 ohms and can cause new faults.

Speak to our team

Questions about vehicle security, tracking or fleet telematics? Our UK team will point you to the right product for your vehicle or fleet.

View all products →
Tags:
  • CAN bus
  • fault finding
  • installers
  • diagnostics
Scorpion Automotive

Alec J.

Software Engineer at Scorpion Automotive

Alec J., a Software Engineer at Scorpion Automotive in Chorley, covers CAN bus, vehicle electronics and electric vehicles.

Reviewed by James M., Technical Director at Scorpion Automotive