Skip to main content
English
OEM and Engineering

UN ECE R116: The Standard Behind Vehicle Alarm Systems

7 min read

By Ian D. Reviewed byJames M.

UN ECE R116: The Standard Behind Vehicle Alarm Systems: Scorpion Automotive guide illustration with an alarm siren icon

UN ECE R116 is the United Nations regulation that sets the approval requirements for vehicle alarm systems, immobilisers and devices that stop unauthorised use of cars and light vans. An alarm or immobiliser approved to R116 has been tested against the same technical rules in every country that applies it.

Key facts:

  • Full title: “Uniform technical prescriptions concerning the protection of motor vehicles against unauthorised use”.
  • Published in the EU’s Official Journal on 16 February 2012 (OJ L 45), incorporating text up to Supplement 3, in force from 23 June 2011.
  • Four parts: devices to prevent unauthorised use, alarm systems, vehicles with an alarm, and immobilisers.
  • Scope: M1 passenger cars and N1 vans, with alarm and immobiliser parts limited to N1 vans of up to 2 tonnes.
  • Proof of approval: an E-mark with the country number, “116R”, the approval number and a letter for the type of device.

What is UN ECE R116?

R116 is one of the UN vehicle regulations adopted under the 1958 Agreement, the framework that lets one country’s type approval be recognised by the others that apply the same regulation. It brought the rules for anti-theft protection into one document.

In the EU, the General Safety Regulation (EU) 2019/2144 lists “protection against unauthorised use, immobiliser and alarm systems” among the type-approval requirements, and points to UN Regulations No 18, No 97 and No 116 for it (Regulation (EU) 2019/2144).

The regulation itself is long, but its job is simple. It defines what each kind of device must do, how it’s tested, and how an approved product is marked so an installer, a vehicle maker or an inspector can tell what they’re looking at.

What are the four parts of R116?

The regulation splits into four parts (R116, OJ L 45):

  1. Part I: approval of M1 and N1 vehicles with regard to their devices to prevent unauthorised use, such as steering locks.
  2. Part II: approval of vehicle alarm systems (VAS) intended to be permanently fitted to M1 cars and N1 vans of up to 2 tonnes.
  3. Part III: approval of a vehicle with regard to its alarm system.
  4. Part IV: approval of immobilisers, and of vehicles with regard to their immobiliser.

Part II and Part IV matter most to the aftermarket. They cover alarms and immobilisers as separate components, which is how an aftermarket system can be approved on its own and then fitted to many vehicles.

The scope also lets countries choose. Each contracting party declares which parts it will mandate for each vehicle category, and fitting Part III or IV equipment to other categories is optional, but anything fitted must still comply.

What must an R116 alarm system do?

An approved alarm has to give a warning signal when someone interferes with the vehicle. The warning must be audible, and it can add optical warnings or a radio alarm.

Some of the requirements in Part II are specific and testable:

  • Detection: the alarm must at least detect and signal the opening of any door, the bonnet and the boot.
  • Siren duration: the audible signal runs for a minimum of 25 seconds and a maximum of 30 seconds, and switching the alarm off cuts it immediately.
  • Climate: parts must work from minus 40°C to plus 85°C in the cabin or boot, and up to plus 125°C in the engine bay unless otherwise specified.
  • Sealing: IP 40 for cabin parts, IP 42 in convertibles where needed, and IP 54 for all other parts.
  • Electromagnetic compatibility: a dedicated annex sets the EMC tests, so the alarm neither false-triggers from interference nor disturbs the vehicle.

The siren limit is the one drivers notice. It’s also why an approved alarm doesn’t sound indefinitely after a single trigger.

What does R116 require of an immobiliser?

Part IV sets out how an immobiliser must stop a vehicle moving under its own power. It allows two approaches:

  • Two circuits: for aftermarket fitting, or a diesel vehicle, the immobiliser must disable at least two separate circuits needed to drive, such as the starter, ignition or fuel supply.
  • Coded control unit: interference by code with at least one control unit the vehicle needs to operate.

It must also set itself without the driver doing anything extra, for example within a maximum of one minute of the key leaving the ignition. On a vehicle with a catalytic converter, it must not let unburnt fuel reach the exhaust.

These rules explain why aftermarket immobilisers interrupt more than one circuit. A single cut wire is easier to find and bridge.

How does R116 differ from Thatcham?

R116 and Thatcham answer different questions, and in the UK you’ll often meet both.

UN ECE R116Thatcham security categories
Who sets itUN vehicle regulation, applied by contracting partiesThatcham Research in the UK
What it provesThe product meets common technical and test rulesThe product meets Thatcham’s attack-resistance criteria for its category
MarkE-mark with “116R” and an approval numberThatcham category (for example Category 1 or 2-1)
Who asks for itType-approval authorities and vehicle makersMainly UK insurers

Thatcham itself notes that its certification does not guarantee insurer recognition, which is negotiated individually (Thatcham Research). For the categories in detail, see our Thatcham security categories guide. For how UK approvals are granted, our guide to VCA approval explains the authority behind the E11 mark.

How do you read an R116 approval mark?

Every approved component carries an international approval mark. Under the regulation it shows:

  • A circle around the letter “E” followed by the number of the approving country, for example 1 for Germany, 4 for the Netherlands or 11 for the United Kingdom.
  • “116R”, a dash and the approval number, to the right of the circle.
  • A symbol for the device type, such as “A” for an alarm system and “I” for an immobiliser.

The regulation also includes a model installation certificate, so the fitter can record how an approved system was installed.

Scorpion alarms approved to R116

Scorpion is a UK manufacturer of vehicle security, supplying the aftermarket and vehicle makers since 1973. Our car alarms and immobilisers include the S-Series range, from the non-Thatcham S4 and S12 to the Category 1 S30 and the Category 2-1 S32, S34 and S37.

For vehicle makers and importers specifying security for a programme, our OEM and bespoke team handles documentation and homologation support alongside engineering. Ask us which approvals apply to the product and market you’re working in.

Talk to us about R116 approved alarms

Specifying an alarm or immobiliser for a vehicle programme, or checking what a product is approved to? Our engineers can talk it through.

Frequently Asked Questions

What does ECE R116 cover?

UN ECE R116 covers the protection of cars and light vans against unauthorised use. Its four parts deal with devices such as steering locks, vehicle alarm systems, vehicles fitted with an alarm, and immobilisers, each with its own technical and test requirements.

How long can an R116 alarm siren sound?

Under R116 the audible signal lasts a minimum of 25 seconds and a maximum of 30 seconds. It may sound again only after a new interference with the vehicle, and switching the alarm off must cut the signal immediately.

Does R116 apply to vans?

Yes, to N1 light goods vehicles. Part I covers M1 and N1 vehicles, while the alarm and immobiliser parts apply to N1 vans with a maximum mass of up to 2 tonnes. Fitting approved devices to other categories is optional, but they must then comply.

Is R116 the same as Thatcham approval?

No. R116 is a UN type-approval regulation shown by an E-mark. Thatcham categories are a separate UK certification run by Thatcham Research and used mainly by insurers. A product can hold one, both or neither, so check each separately.

What does “116R” on a label mean?

It shows the product was approved under UN Regulation No 116. The number after the dash is the approval number, the figure in the circle is the approving country, and a letter such as “A” or “I” shows whether it’s an alarm or an immobiliser.

Speak to our team

Dealers, installers and OEM partners get trade pricing, product training and a named account manager. Tell us what you need.

View all products →
Tags:
  • standards
  • vehicle alarms
  • immobilisers
  • type approval
Scorpion Automotive

Ian D.

Head of R&D at Scorpion Automotive

Ian D. is Head of R&D at Scorpion Automotive in Chorley and writes about Thatcham, insurance and OEM engineering.

Reviewed by James M., Technical Director at Scorpion Automotive