Campervan Security for Conversions: What to Fit and When
By Mike B. Reviewed byJames M.
Campervan security is easiest to get right before the walls go in. On a conversion, plan the immobiliser, alarm sensors and tracker wiring while the van is still a bare shell, then add locks and habits once it’s on the road. Retrofitting later is possible, but panels, insulation and furniture make every cable run harder.
The short version:
- Plan early: decide on sensors and cable routes before lining and insulation.
- Immobiliser first: most conversions start life as vans with keyless or key-programmable starting.
- Alarm with habitation cover: protect the living area and lockers as well as the cab.
- Tracker: fit it out of sight and away from where a thief would look.
- Tell your insurer about the conversion and what you’ve fitted.
Why does campervan security need planning?
A converted campervan is worth more than the van it started as. It carries a kitchen, a bed, solar kit, bikes and often the owners’ holiday gear. It’s also, underneath, a popular panel van that thieves already know how to steal.
That combination means two kinds of risk:
- Theft of the whole van, using the same keyless, relay or diagnostic-port methods used on the base vehicle.
- Theft from the van, through the sliding door, rear doors, windows or rooflights.
Self-builders tend to focus on layout and electrics. Security is often an afterthought, fitted once the interior is finished, when it’s hardest to do well.
What should you fit during the build?
Some security work belongs in the build itself, because it needs access behind panels.
- Bare shell stage. Agree where the alarm’s sensors will sit and run any cables before insulation. Note where the tracker will go so it’s hidden but has power.
- First fix electrics. If the habitation area has its own leisure electrics, make sure security kit is wired to the right supply and won’t flatten the starter battery.
- Before furniture. Check the locations of any interior sensors against curtains, cupboards and the bed. A sensor that’s blocked by a curtain or a cupboard door is no use.
- Before lining the doors. Add any extra locks or reinforcement to the sliding and rear doors.
If you’re using a professional converter, ask them to bring your installer in at the shell stage.
Which immobiliser suits a campervan conversion?
Most conversions are built on panel vans that thieves target for the base vehicle alone. The factory immobiliser trusts the key, so a cloned or newly programmed key will start the van.
An independent immobiliser adds a check the thief can’t pass. The X-Series immobiliser connects to the van’s CAN bus and arms itself when the ignition goes off. To drive away, you enter a custom PIN on the van’s own buttons and switches, or use a driver tag. There’s no keypad on show, so it’s hard for a thief to spot.
Because it’s fitted to the base vehicle’s wiring rather than the habitation area, the X-Series can go in at any stage of a conversion. It’s still easier while panels are off.
Which alarm suits a campervan?
A campervan alarm has to cover the cab and the living area. Our motorhome alarm guide goes into the detail; the short answer is the same for most campervans.
Things to check:
- Habitation and locker cover. The S37 in our S-Series alarms range is a Thatcham 2 to 1 CAN-Bus upgrade alarm with a built-in RF receiver for wireless PIR sensors, and it’s suitable for motorhomes. Wireless sensors avoid cable runs through finished furniture.
- Curtains and blinds. Ultrasonic sensors fill the cabin with sound waves, and heavy curtains can get in the way. Scorpion’s own microwave intrusion sensor work, described on our bespoke vehicle electronics page, was used for exactly this reason in vehicles where curtains interfere with ultrasonics.
- Night arming. You’ll want doors protected while you sleep inside without the interior sensors triggering.
Campervan security checklist: what and when
| Item | Best fitted at | Why |
|---|---|---|
| Alarm sensor positions and cables | Bare shell | Access behind panels and under floors |
| Tracker location and power | Bare shell or first fix | Hidden mounting with a reliable supply |
| CAN bus immobiliser | Any stage, easiest early | Wired to the base vehicle, not the habitation area |
| Extra door locks | Before door cards go on | Room to fit and reinforce |
| Wireless PIR sensors | After furniture | Placed where the layout actually allows |
| Window and rooflight security | After the build | Matched to the final fittings |
A conversion hidden inside an industrial unit is hard to find by GPS alone. Scorpion is building the VHF+ Recovery Network to add a radio beacon for that final search, and it doesn’t tie a build to one tracker brand.
Insurance and paperwork
Converting a van changes what you’re insuring. Tell your insurer about the conversion and the security you’ve fitted, and keep receipts and certificates. Some insurers ask for a particular Thatcham category of alarm or a monitored tracker on higher-value campervans, so check before you buy.
Talk to us about securing a conversion
Tell us the base vehicle and where your build is up to, and we’ll suggest the right immobiliser and alarm setup.
- Speak to us about campervan security
- X-Series immobiliser for the base vehicle
Frequently Asked Questions
What is the best security for a campervan?
Most campervans need an independent immobiliser for the base van, an alarm that covers the cab and the living area, and a hidden tracker. Physical locks on the sliding and rear doors add a visible deterrent.
When should I fit an alarm to a campervan conversion?
Plan it at the bare shell stage, before insulation and lining, so sensor cables and the control unit can be placed properly. Wireless sensors can be added after the furniture goes in, once you know exactly where they’ll work.
Do curtains affect a campervan alarm?
They can. Ultrasonic interior sensors rely on sound waves filling the cabin, and heavy curtains or blinds can block them. Wireless PIR sensors placed in each zone, or microwave sensors, avoid the problem.
Does a campervan need an immobiliser?
If it’s built on a modern van, an independent immobiliser is strongly worth having. Factory systems trust the key, so a cloned or reprogrammed key will start the van. A CAN bus immobiliser such as the X-Series needs your PIN as well.
Do I need to tell my insurer about a campervan conversion?
Yes. A conversion changes the vehicle’s value and use, and an insurer that doesn’t know about it may not pay out. Tell them what you’ve converted and what security you’ve fitted.
Speak to our team
Questions about vehicle security, tracking or fleet telematics? Our UK team will point you to the right product for your vehicle or fleet.
Related Products
View all products →- campervan security
- van conversions
- X-Series
- S-Series
Mike B.
Software Engineer at Scorpion Automotive
Mike B. is a Software Engineer at Scorpion Automotive in Chorley. Vehicle security, immobilisers and keyless theft are the areas Mike covers.
Reviewed by James M., Technical Director at Scorpion Automotive